Відео

It's OK in a pinch. Disposable lighters are very cheap. But it's always good to learn something new.

Looks great, except your trigger is exposed

God loves you beautiful angel

I can't keep a lighter long enough to refill it.

Stunning

it's called a polyphilic reaction.

Omg the rubber band trick works for me and we have the same butane 💪🏿🔥🔥

Appreciate the video man i checked out the video before this one and it was frest as well. Just saved me from throwing sway a special lighter kne if my kady friends gave me

RIP pete 😔

can't you use the pressure and the bb to seal it?

You recycle them in the yellow trash can♻️,

Great job Pete

Its the water thats activates the glue. That why it sticks to skin easily.

Where did you find a fan?

it seems one can use a valve from old bicycle tires

Upgraded crack lighters who has a needle size to poke a note in the bottom on a regular what you want me to go to a elementary and take one out the wall 😂😂😂😂😂

It didn’t work I typed pulling the valve and not pulling the valve and it only lost pressure

Still won’t fill

They stopped making that lathe and I've been looking for one everywhere. There are some in FB marketplace but way on the other side of the state so I'm going it with a non variable 14 inch delta.. but I'm gonna use a brand new conversion kit just because it doesn't have the extra headstock space the CM 12x33 has

You don't need that main wheel

just use clipper lighters

Thanks 🕊️

Did you consider just grinding a flat on the end of the rod rather than grinding a slot? I've been considering that and wonder if there is an advantage to either way?

I have a lot of Bernzomatic oxygen tank，is only have 40g 😢 Can I refill it？

Absolutely beautiful! I'm going to be retrofitting my Grandmother's grandfather clock with glass shelves and lighting to make it into a curio cabinet. You've given me ideas as well as inspiration to dive into the project. Thanks so much!

I did this I thought I I invented the idea only thing I did differently was I beveled the hole just enough to get the butane tip to fit air tight so I basically coned the whole lol buy works great I was just showing my wife that then I see this video 😂

No is not safe you must refil exatly 370gr propane , so you have to turn it using a scale , to do that neded a a rubber band adaptor

I want to do exactly what you did minus the outlet. I want to use it as a work desk/ homework desk - put a couple of computers on it. I’m new to woodworking so it sounds like a stupid question but what is the purpose of building a frame before you put the top piece on? Isn’t that a lot of weight to screw into the walls?

Wtf lolololololl

Use bleach. Its what actually is activator. It's why the store stuff has essential oil added to it. It masks the smell.

what hardware did you use for hinges?

Wish I could buy the fan as it's NLA and armature is like $200. I bought the 690LR from Home Depot back in 2004 and it's like brand new as I've only used it for a few hours. Figure buy a tool to last me forever... For those that can find a fan, a much easier method is to put armature in freezer for 2 hours and heat fan in some 300F veggie oil. It should drop right down the shaft as this is how they probably did it at the factory. Basically the inner sleeve is 0.001 smaller than the shaft. Cooling armature shrinks the shaft and heating fan increases collar ID. You''ll only have a few seconds, so get that socket ready to tap it in place if it doesn't drop on.

I'm assuming he already got injured doing this incorrectly by the look of his hand...mapp and propane are different sir

Wow , What a great Project… Blessings from Gettysburg Pa…

I've just GOTTA try this and see if I can add some different COLORS to enhance the effect!

Cool walk around tour! Thanks for showing me your shop.

Great video on how to repurpose an accessory. BTW the $55 hold down you showed isn’t available for new purchase but there are some on eBay. I have been trying to add something like this and your video has provided a key. I also have the Delta table saw like yours. Many people scorn the factory miter gauge but don’t listen to them. I bought an aftermarket miter gauge for “accuracy” but it doesn’t work any better so I’m happy using the original miter gauge.

Thank you, sir !!!

Or just buy a refillable lighter.

@2:00 is it the alcohol or the idodine it's reacting to.. that bottle has 40% alcohol in it .. not pure iodine

One thing my mom left behind when she died was a solid blue bic lighter covered in little happy face stickers. This video helped me refill that lighter when it died, so, this video is a win for me. Thanks man.

Doesn't look anything like the miter gauge in the lead-in thumbnail.

Just hold the lighter open like you are lighting the lighter and fill it up from the top then you would not have to put the pin in the bottom like that. All it is at the top is a small valve when it is opened up it don't care what way the gas goes whatever side has more pressure will win.

just realized mine just had cotton from my jean pockets jammed in the front in a bit lmao. Figured that since I couldn't hear a hiss that it was empty but nah the cotton just stopped the hiss noise too.

Dont know why everyone keeps trying to fill these from the bottom... Just think of, "where it comes out it goes in" I do refill them through the nozzle by pressing the lever, works absolutely fine and now pin's required and 100% leaksafe because of not need to plug any holes 😬

Buy a refillable lighter... lmao

Absolutely gorgeous humidor, great work 👍

You're a champion mate not only is it expensive, you usually have to get it on line. Well I do, anyway. It's not really sold at the bigger hardware chains

What handwheel did you get

Tried this seemed to fry a bit faster but left a white residue - was using gorilla super glue and used 70% and 91% - the 70% may have dried it a bit faster